Troubleshoot

Symptoms of Bad Sway Bar Bushings

Pearl white Toyota Camry raised on a two-post lift in a workshop, seen past shelving stacked with parts boxes

A clunk from the front of the car every time you go over a speed bump at an angle. A creak or squeak over driveway ramps, worse on cold mornings. A car that leans a little more in corners than it used to. These are the kinds of small, annoying suspension noises that very often trace back to two cheap rubber parts: the sway bar bushings.

Sway bar bushings rarely cause anything dangerous, and they are one of the cheaper suspension repairs. The difficulty is that several suspension parts make similar noises. This guide explains what the bushings do, the symptoms of worn ones, how to tell them apart from sway bar links and other suspension parts, how to test them, and what replacement costs.

The common symptoms at a glance:

SymptomWhat You NoticeHow Urgent
Clunk or knock over bumpsDull thud from one corner over speed bumps, potholes or driveway rampsLow to moderate
Squeak or creakRubbery squeak over bumps or when rocking the car, often worse when coldLow
More body rollCar leans more in corners and feels less plantedModerate
Vague handlingLess precise steering in turns or lane changesModerate
Rattle on rough roadsLight rattling over broken pavementLow
Visible wearCracked, torn, flattened or oval-shaped rubber; bar moving in its mountsReplace soon

Worn sway bar bushings are rarely an emergency, but get any new clunk checked before assuming it is the bushings. A loose ball joint, tie rod end or control arm makes similar noises and is far more serious. If the noise comes with wandering steering, uneven tire wear or a pull to one side, have the front suspension inspected promptly.

What Sway Bar Bushings Do

A sway bar, also called a stabilizer bar or anti-roll bar, is a steel bar running across the car that links the left and right suspension. When the car leans in a corner, the bar twists and resists the lean, keeping the body flatter. Most cars have one at the front, and many have one at the rear as well.

The bar is attached to the car in two ways. In the middle, two rubber or polyurethane bushings clamp it to the subframe or chassis with metal brackets, letting it rotate while holding it in place. At each end, a sway bar link connects it to the suspension. The bushings are the pivot; the links are the connection. Both wear out, and both make noise when they do. Our guide to bad sway bar links covers the link side.

Why Sway Bar Bushings Wear Out

The bushings are rubber clamped around a moving steel bar, exposed to road dirt, water and salt. Over time the rubber hardens, cracks and wears, and grit gets between the rubber and the bar, grinding the bushing away until it no longer grips. Mazda’s service bulletin for the 2010 to 2013 Mazda3 describes exactly this: a squeaking or knocking noise from the rear over bumps, caused by dust entering between the rear stabilizer bushing and stabilizer bar, which wears down the bushing.

Bushings can also be the problem when they are new. A badly made or poorly bonded bushing can squeak from day one. Tesla issued a service bulletin for some 2019 to 2020 Model S and Model X vehicles whose front stabilizer bars had improperly vulcanized bushings that make a squeak noise when driving over road imperfections. Oil leaks soak and soften rubber bushings too, and aftermarket polyurethane bushings squeak if they are not greased.

Symptoms of Bad Sway Bar Bushings

1. Clunking or knocking over bumps

Once a bushing has worn loose, the bar can move up and down or shift sideways inside its bracket, and it knocks against the bracket over bumps. The noise is usually loudest when one side of the car rises more than the other, such as taking a speed bump at an angle or driving over a curb-side drain, because that is when the bar twists. It is typically a dull thud rather than a sharp metallic bang.

2. Squeaking or creaking

A dry, hardened or worn bushing squeaks or creaks as the bar rotates against it. The sound is often most obvious at low speed over bumps, on cold mornings when the rubber is stiff, or when you rock the car by hand at a corner. It tends to come from roughly the center of the front of the car, where the bushings are mounted.

3. More body roll in corners

With loose bushings the bar has to move before it starts to resist the lean, so the car rolls more before the bar takes effect. You may notice more lean in corners, a looser feel in quick lane changes, or a car that feels less settled on winding roads.

4. Vague or less precise handling

The sway bar contributes to how quickly and precisely the car responds when you turn the wheel. Worn bushings make the response slightly delayed and less crisp. On their own they rarely cause the wandering or pulling associated with steering components, so if those symptoms are present, look elsewhere too.

5. Rattling on rough roads

Over broken pavement or gravel, a loose bar can produce a light rattle or buzz as it moves in its mounts.

6. Visible wear

With the car safely raised, the bushings are usually easy to see on the subframe. Look for rubber that is cracked, torn, flattened on one side, squeezed out of its bracket, or worn into an oval so the bar sits loose. A shiny, polished band on the bar next to the bushing shows the bar has been moving where it should not.

Bushings, Links or Something Else?

Several suspension parts produce similar clunks and squeaks over bumps. Some clues:

  • Sway bar links usually rattle or clunk over smaller, choppier bumps and often have a visible loose or torn ball joint at the end of the link. The bushings tend to squeak more and clunk over larger, uneven bumps.
  • Control arm bushings clunk when braking or accelerating as well as over bumps, and can cause shimmy or wandering. Our guide to worn control arm bushings covers those.
  • Strut mounts clunk or creak when turning the steering wheel at low speed, especially while parking. See our guide to the symptoms of a bad strut mount.
  • Ball joints clunk and can cause wandering steering and uneven tire wear, and a badly worn one is a safety issue. Our guide to the symptoms of a bad ball joint explains the checks.

For a broader list of what clunks over bumps, our guide to why the suspension clunks only over bumps walks through all of them.

How to Test Sway Bar Bushings

  1. Rock the car. Push down hard on one front corner and let it rebound, then do the other side. A squeak or knock from the center front points toward the bushings.
  2. Inspect them visually with the car safely supported on ramps or jack stands, never on a jack alone. Look for the wear signs above.
  3. Pry on the bar. With a pry bar, gently lever the sway bar up and down next to each bushing. A good bushing allows almost no movement; a worn one lets the bar shift and often clunks.
  4. Disconnect the links. This test comes straight from Mazda’s bulletin: drive over a bump with the stabilizer links disconnected, and if the noise is gone, the causal part is the rear stabilizer bushings. It works the same way at the front. Only drive the car this way briefly and slowly, as a test, then reconnect the links.
  5. Use a chassis stethoscope or electronic chassis ear if you have access to one, which shops use to pinpoint noises while the car is driven.

Replacing Sway Bar Bushings

On most cars this is a straightforward job: unbolt the two brackets, slide the old bushings off, fit the new ones and bolt the brackets back. Some vehicles need the subframe lowered or other parts moved for access. A few tips:

  • Replace both sides together, and consider the links at the same time if they show any wear.
  • Clean the bar where the bushings sit. Rust and grit there will wear new bushings quickly.
  • Follow the instructions for lubrication. Polyurethane bushings usually need the grease supplied with them or they will squeak. Rubber bushings vary, so follow the manufacturer’s guidance.
  • Tighten the brackets with the car at ride height, resting on its wheels or with the suspension supported, so the bushings are not preloaded in a twisted position.
  • Check for a service bulletin. Some models have a known fix, sometimes a revised bar with new bushings, as in the Mazda and Tesla bulletins above. A dealer can check by VIN.

Rubber bushings give a quieter, more comfortable ride. Polyurethane bushings are firmer, last longer and sharpen handling slightly, at the cost of more noise and the need for grease.

What It Costs

RepairTypical Cost
Pair of sway bar bushings (part)$10 to $60
Bushings replaced at a shop$100 to $300
Bushings and both sway bar links replaced$200 to $450
Sway bar replaced with bushings$300 to $800 or more

Access makes the difference. On some vehicles the brackets are easy to reach from below; on others the subframe has to be dropped, which adds labor.

Can You Keep Driving With Bad Sway Bar Bushings?

Generally, yes. Worn sway bar bushings make noise and reduce handling precision, but they do not usually affect steering or braking directly, and the bar is still attached. Most people replace them because the noise is annoying, which is a fine reason.

Do not leave them indefinitely, though. A bar that moves in loose bushings puts extra wear on the links and brackets, and the car will be less stable in an emergency lane change. More importantly, make sure the noise really is the bushings, because a clunk from a worn ball joint or tie rod end is a much more urgent problem.

Sway Bar Bushing Questions Answered

What are the symptoms of bad sway bar bushings?

Clunking or knocking over bumps, especially uneven ones, squeaking or creaking over bumps or when rocking the car, more body roll in corners, slightly vague handling, rattling on rough roads, and visibly cracked, torn or oval-shaped bushings.

How do I tell bad sway bar bushings from bad sway bar links?

Links usually rattle or clunk over small, choppy bumps and often have a visibly loose ball joint at the end. Bushings tend to squeak and clunk over larger, uneven bumps from the center of the car. Disconnecting the links and driving over a bump briefly can confirm the bushings: if the noise disappears, the bushings are the cause.

Can bad sway bar bushings cause a clunking noise?

Yes. Once a bushing wears loose, the bar can move in its bracket and knock over bumps, especially when one side of the car rises more than the other, such as on a speed bump taken at an angle.

Is it safe to drive with worn sway bar bushings?

Generally yes in the short term. They mainly cause noise and reduced handling precision. Replace them in reasonable time, and have the suspension checked to rule out worn ball joints or tie rod ends, which make similar noises and are more serious.

Should I lubricate sway bar bushings?

Polyurethane bushings usually need grease, and squeak without it. Rubber bushings vary by manufacturer, so follow the instructions supplied with them. Spraying lubricant on old, worn bushings may quiet a squeak briefly but does not fix them.

How much does it cost to replace sway bar bushings?

The bushings themselves usually cost $10 to $60 a pair. Shop replacement typically runs $100 to $300, and more if the subframe has to be lowered or the links are replaced at the same time.

As an Amazon Associate we earn from qualifying purchases.

About the author

The Motor Guy

The Motor Guy is a passionate car enthusiast with a love for troubleshooting and diagnosing all sorts of vehicle problems.

With years of experience in OBD diagnostics, he has become an expert in identifying and solving complex automotive issues.

Through TheMotorGuy.com, he shares his knowledge and expertise with others, providing valuable insights and tips on how to keep your vehicle running smoothly.

Qualifications:
- 12 years experience in the automotive industry
- ASE Master Automobile Technician
- A Series: Automobile and Light Truck Certification, A9 Light Vehicle Diesel Engine Certification
- Bachelor's Degree in Information Systems