Troubleshoot

P0307 Code: Cylinder 7 Misfire — Causes & How to Fix

Dark green Ford Expedition with its hood open at the front of a row of workshop bays

P0307 means the engine computer has detected repeated misfires in cylinder 7. That tells you two things before you open the hood. First, your engine has at least eight cylinders, because four- and six-cylinder engines have no cylinder 7, so this is almost always a V8 (or occasionally a V10 or V12). Second, the fault is confined to one cylinder, which makes it far easier to pin down than a random misfire. The catch is that on a V8, cylinder 7 is in a different place depending on who built the engine, and on many GM V8s it is one of the cylinders the engine shuts down to save fuel, which brings the valvetrain into play. This article covers where cylinder 7 is, the six causes in order of likelihood, the swap test that separates them, and what each repair typically costs.

Start with the table, then read the note under it.

CauseTelltale SignTypical Cost
Worn or fouled spark plugPlugs past their service interval; misfire worse under load$20 to $300 (a full set)
Failed ignition coil or bootMisfire moves to another cylinder when the coil is swapped$60 to $300
Clogged or failed fuel injectorMisfire stays with the injector; cylinder 7 runs lean$150 to $500
Vacuum leak near cylinder 7Misfire mostly at idle; hissing near the rear of the intake$20 to $600
Valvetrain fault (lifter, cam lobe, valve, spring)Ticking noise; misfire does not follow coil, plug or injector$300 to $4,000+
Low compression (head gasket, valve, rings)Low compression or high leakdown on cylinder 7$1,200 to $4,000+

Stop driving if the check engine light is flashing, or if the engine is shaking hard, losing power or smells of raw fuel. A flashing light means the misfire is severe enough to send unburned fuel into the exhaust, where it can overheat and destroy the catalytic converter within a short drive. If the light is steady and the engine runs reasonably smoothly, it is generally safe to drive gently and briefly to a shop, but do not tow, carry heavy loads or drive hard until it is fixed.

What the P0307 Code Actually Means

The engine computer watches the crankshaft’s speed through every revolution. Each cylinder’s firing gives the crank a small push, and when a cylinder fails to fire properly that push is missing, so the crank slows slightly at that point. The computer knows the firing order, so it can tell which cylinder missed. When misfires in cylinder 7 cross the manufacturer’s threshold over a set number of revolutions, it stores P0307: “Cylinder 7 Misfire Detected”.

The misfire monitor has two levels. A lower rate that would raise emissions sets the code and turns on a steady check engine light. A higher rate that risks overheating the catalytic converter makes the light flash. The freeze frame data stored with the code is worth reading: engine speed, load and coolant temperature at the moment it set tell you whether the misfire happens cold, at idle or under load, and each points toward different causes.

Where Is Cylinder 7? It Depends on the Maker

Before you touch a coil or plug, find the right cylinder. Manufacturers number V8 cylinders differently:

  • GM V8s (small-block, LS, LT and Vortec truck engines): odd-numbered cylinders 1, 3, 5 and 7 are on the driver’s side, front to back, so cylinder 7 is the rearmost cylinder on the driver’s side.
  • Chrysler Hemi V8s follow the same odd-on-the-driver’s-side pattern, so cylinder 7 is again at the rear of the driver’s side bank.
  • Ford V8s (modular 4.6 and 5.4, Coyote 5.0 and the 6.2): cylinders 1 to 4 run front to back on the passenger side and 5 to 8 on the driver’s side, so cylinder 7 is the third cylinder back on the driver’s side.

Other makers use their own schemes, so confirm with the service information or the cylinder numbers often cast into the intake manifold before swapping anything. Swapping the wrong cylinder’s coil wastes the most useful test you have.

The Swap Test: Make the Misfire Move

Because P0307 names one cylinder, you can find most causes by moving parts and watching whether the code moves with them. Swap the cylinder 7 coil with a neighbor’s, clear the codes and drive. If the code comes back as the neighbor’s number (for example P0305), the coil is bad. If it stays P0307, swap the spark plugs the same way. If it still stays, swap the injectors where that is practical, or have them tested. A misfire that stays in cylinder 7 no matter which parts you move points to something that does not move: a vacuum leak at that port, the valvetrain or compression.

That last outcome is where cylinder 7 is different on many GM V8s. If you are unsure whether you are looking at a plug or a coil problem, the guide to telling a bad spark plug from a bad ignition coil covers the visual signs.

Symptoms You May Notice Alongside the Code

  • A rough or shaking idle, often easiest to feel at a stop in Drive
  • Hesitation, stumbling or loss of power under acceleration or when towing
  • A flashing check engine light during hard acceleration
  • Poor fuel economy and a fuel smell from the exhaust
  • A ticking noise from the engine, if the cause is in the valvetrain
  • Other codes: P0300 for random or multiple misfires, a lean code, or misfires on other cylinders

A V8 has enough cylinders that a single misfire can be surprisingly mild to drive with, which is why P0307 often goes unnoticed until the light appears. If the light is flashing rather than steady, see why the check engine light flashes while driving.

1. Worn or Fouled Spark Plug

A worn plug needs more voltage to fire across its widened gap, and under load, when cylinder pressure is highest, the spark may not make it. Plugs can also foul with oil, carbon or coolant. Pull the cylinder 7 plug and look at it: a gap far past specification, heavy black carbon, wet oil or a white, clean-washed look each tells a story. Oil on the plug usually means worn valve guide seals or rings, and a steam-cleaned look can mean coolant is getting in.

On a V8 that is past its plug interval, replace the full set rather than one plug. The rear plugs are often the hardest to reach, which is one reason cylinder 7 and 8 plugs sometimes get skipped at service time. The bad spark plug symptoms guide covers what each plug condition means.

2. Failed Ignition Coil or Boot

Most modern V8s use one coil per cylinder. Coils fail from heat and age, and the rubber boot that connects the coil to the plug can crack and let the spark track to the cylinder head instead of firing the plug. Look for white or black carbon tracks on the boot, cracks in the coil body and oil in the plug well, which degrades the boot. Older V8s with a distributor or plug wires can have the same fault in the cylinder 7 wire.

The swap test is the cleanest proof: if the misfire follows the coil to another cylinder, replace the coil. The bad ignition coil guide covers the other signs.

3. Clogged or Failed Fuel Injector

If cylinder 7 is not getting enough fuel, it runs lean and misfires, typically at idle and light load. Injectors clog with deposits, stick, leak or fail electrically, and the connector can corrode or work loose. With the engine idling, a mechanic’s stethoscope on the injector should pick up a steady clicking. A noid light shows whether the injector is getting its pulse. Many scan tools can also run a cylinder contribution or injector balance test.

On port-injected V8s, injectors can often be swapped between cylinders for the same move-the-misfire test as the coil. Direct-injection injectors are a bigger job and are better tested in place. The guide to diagnosing a faulty fuel injector walks through the tests.

4. Vacuum Leak Near Cylinder 7

A leak at the intake manifold gasket next to cylinder 7’s port, or a cracked hose or fitting nearby, lets extra air into that cylinder alone. It runs lean and misfires, most noticeably at idle when manifold vacuum is highest, and the misfire often clears up as engine speed rises. Because cylinder 7 sits at the rear of the engine on many V8s, near the back of the intake manifold, leaks there are easy to miss.

Listen for hissing at idle, check the PCV and brake booster hoses at the back of the intake, and use a smoke test if nothing obvious turns up. A misfire that stays in cylinder 7 through the swap tests, is worst at idle and comes with lean fuel trims is a strong hint.

5. Valvetrain Fault: Lifter, Cam Lobe, Valve or Spring

This is the cause that sets P0307 apart on GM V8s. Engines with Active Fuel Management (AFM), and its successor Dynamic Fuel Management, shut down half the cylinders at light load using special collapsible lifters. On GM V8s with AFM, the deactivating cylinders are 1, 4, 6 and 7. GM’s service bulletin 19-NA-219, which covers 2002 to 2018 GM V8 cars and trucks, explains that an AFM lifter that unlocks as soon as the engine starts causes misfires on cylinder 1, 4, 6 or 7 with P0300 and usually no noise. A lifter that is mechanically collapsed or stuck adds a consistent valvetrain tick.

The same bulletin lists the other valvetrain faults that cause a misfire which ignition and fuel parts will not fix: a worn cam lobe or lifter roller, a sticking valve, valve leakage and a broken valve spring. It gives some useful pointers:

  • A noise from a worn lobe or lifter will not go away when the injectors are cancelled, and it runs at camshaft speed, half of crankshaft speed.
  • Measuring rocker arm lift at the pushrod side and comparing cylinders on the same bank shows a worn lobe or collapsed lifter as noticeably less lift.
  • A sticking valve is suggested if misfires keep counting during an aggressive deceleration with engine braking.
  • A cylinder leakage test should show valve leakage, while a compression test often will not unless the leakage is severe.

If a worn lobe or lifter roller is found, GM’s procedure is to replace the camshaft and all the lifters, not just the one that failed, and on AFM engines also the oil manifold filter screen under the oil pressure sensor. That is why this cause covers such a wide cost range. For more on the noises involved, see the guide to lifter tick causes and fixes.

6. Low Compression

If cylinder 7 cannot hold compression, it cannot fire properly however good the spark and fuel are. A head gasket leaking between cylinders or into a coolant passage, a burnt valve or worn or stuck piston rings are the usual reasons. A compression test compares cylinder 7 with the others on the same engine, and a leakdown test shows where the air escapes: bubbles in the coolant for a head gasket, hissing at the tailpipe or intake for a valve, or air from the oil filler for the rings.

Coolant loss with white exhaust smoke, or a plug that looks steam-cleaned, points toward a head gasket. These are the most expensive outcomes, so confirm them with a test rather than assuming them.

How to Diagnose P0307 in the Right Order

  1. Read every code and the freeze frame. Note engine speed, load and temperature when P0307 set, and whether other misfire or lean codes are stored.
  2. Check for service bulletins. Some misfire codes are software issues. Audi’s bulletin 2032222 for the 2013 RS5, for example, covers misfire codes P0300 to P0308 where “replacing the ignition coils and spark plugs does not fix the problem”, and the fix is an engine computer software update.
  3. Find cylinder 7 for your engine using the numbering above or the service information.
  4. Inspect the plug, coil, boot and connector on cylinder 7, and the plug well for oil.
  5. Swap the coil with a neighbor, clear codes and drive. If the misfire moves, replace the coil.
  6. Swap or replace the plug, then test the injector, repeating the move-the-misfire check each time.
  7. Look for vacuum leaks around the rear of the intake if the misfire is worst at idle.
  8. Run compression and leakdown tests if the misfire stays in cylinder 7. On a GM V8 with AFM, check rocker lift and listen for a tick before assuming a head gasket.

What not to do: do not replace all eight coils, or the injectors, on the strength of a single-cylinder code. Do not keep driving with a flashing light to “see if it clears”. And on a GM V8 with AFM, do not assume a misfire that survives new plugs and a coil swap is a head gasket. A lifter is a common and very different repair.

P0307 Repair Cost

These are typical ranges for common V8 cars and trucks. Prices vary with region, labor rates and engine, especially how hard the rear cylinders are to reach.

RepairTypical Cost
Diagnostic fee at a shop$100 to $180
Spark plug, one (DIY)$10 to $30
Full set of V8 spark plugs, installed$150 to $400
Ignition coil, installed$60 to $300
Fuel injector, installed$150 to $500 (more for direct injection)
Intake manifold gasket$300 to $800
AFM lifter, camshaft and lifter replacement$1,500 to $4,000+
Head gasket$1,500 to $4,000+

The swap test costs nothing but time and catches the cheapest and most common causes. It is worth doing before paying for anything else.

Can You Keep Driving With P0307?

With a steady light and an engine that runs reasonably smoothly, you can usually drive gently for a short time to get it diagnosed. Every misfire sends unburned fuel into the exhaust, so do not leave it for weeks: a persistent misfire can damage the catalytic converter, which costs far more than a coil or plug.

With a flashing light, stop as soon as it is safe and have the vehicle checked or towed. The same applies if the engine shakes heavily, loses significant power or smells strongly of fuel. If a valvetrain tick has appeared alongside the misfire, avoid hard driving and towing until it has been inspected, because a failing lifter or cam lobe can shed metal into the oil.

Related Codes

  • P0300: random or multiple misfires. P0300 together with P0307 can mean a shared cause affecting several cylinders, with cylinder 7 the worst. On GM AFM V8s, P0300 with misfires on 1, 4, 6 or 7 is the lifter pattern.
  • P0306: the same fault in cylinder 6. On a GM V8, cylinders 6 and 7 are both AFM cylinders, but on opposite banks.
  • P0308: the same fault in cylinder 8. On a GM or Hemi V8, cylinder 8 is directly across from cylinder 7 at the rear of the passenger side, so misfires on both point to something shared at the back of the engine.
  • P0301 to P0305: the same fault in cylinders 1 to 5, diagnosed the same way.
  • P0171 and P0174: a lean condition on bank 1 or bank 2. Cylinder 7 is on bank 1 on GM and Hemi V8s and on bank 2 on Ford V8s. If the lean code is for cylinder 7’s bank, look for a vacuum leak or a fuel delivery problem before blaming the ignition.

If the misfire is worst at idle, the guide to why an engine misfires at idle covers the idle-specific causes in more depth.

P0307 Questions Answered

What does the P0307 code mean?

P0307 means the engine computer has detected repeated misfires in cylinder 7. Since only engines with eight or more cylinders have a cylinder 7, it almost always appears on a V8. The usual causes are a worn spark plug, a failed ignition coil or a fuel injector problem, with vacuum leaks, valvetrain faults and low compression less common.

Where is cylinder 7 on a V8?

It depends on the maker. On GM and Chrysler Hemi V8s, odd cylinders are on the driver’s side, so cylinder 7 is the rearmost cylinder on that side. On Ford V8s, cylinders 5 to 8 are on the driver’s side, so cylinder 7 is the third one back. Always confirm with the service information before swapping parts.

How much does it cost to fix P0307?

Often under $300. A spark plug or ignition coil typically costs $60 to $300 installed, and a fuel injector $150 to $500. Valvetrain repairs such as an AFM lifter and camshaft replacement on a GM V8, or a head gasket, typically run $1,500 to $4,000 or more.

Is it safe to drive with a P0307 code?

With a steady check engine light and a smooth-running engine, you can usually drive gently for a short time to get it diagnosed. If the light is flashing, the engine shakes badly or you smell fuel, stop driving, because the misfire can overheat and ruin the catalytic converter.

Why does P0307 keep coming back after new plugs and a coil?

If the misfire stays in cylinder 7 after the plug and coil are replaced, look at the injector, a vacuum leak near that cylinder, the valvetrain and compression. On GM V8s with Active Fuel Management, cylinder 7 is one of the deactivating cylinders, and a collapsed or stuck AFM lifter is a documented cause.

What is the difference between P0300 and P0307?

P0307 pins the misfire to cylinder 7, which points to a part serving that cylinder. P0300 means misfires are random or spread across several cylinders, which points to something shared, such as fuel pressure or a vacuum leak. When both are stored, cylinder 7 is usually the worst affected.

As an Amazon Associate we earn from qualifying purchases.

About the author

The Motor Guy

The Motor Guy is a passionate car enthusiast with a love for troubleshooting and diagnosing all sorts of vehicle problems. He started TheMotorGuy.com in early 2017 after learning to service and repair his own BMW and VW cars.

With years of experience in OBD diagnostics, and a background in information systems that suits the data side of modern vehicles, he shares practical guides on keeping your vehicle running smoothly. Guides are researched from manufacturer service information, NHTSA recall and safety data and other primary sources, which are cited in each article.

Qualifications:
- First Class Honours Degree in Information Systems