Troubleshoot

P0107 Code: MAP Sensor Low Input — Causes & How to Fix

Dark grey Volkswagen Jetta on a low ramp in a clean repair workshop, seen from floor level

P0107 means the engine computer is reading a voltage from the manifold absolute pressure (MAP) sensor that is lower than the sensor should ever produce. It is easy to assume that means a vacuum leak or a boost problem, and that assumption sends a lot of people looking in the wrong place. A vacuum leak actually pushes the MAP reading up, not down, so it cannot set P0107. A reading stuck at the bottom of the scale is an electrical signal: a bad connector, a lost 5-volt supply, a shorted wire or a failed sensor. This article covers how the MAP sensor works, the six causes in order of likelihood, a key-on test that tells you within a minute whether the problem is electrical, and what each repair typically costs.

Start with the table, then read the note under it.

CauseTelltale SignTypical Cost
Loose, corroded or poorly crimped connectorCode comes and goes; reading drops out when the plug is wiggled$0 to $200
Shorted 5-volt reference circuitOther sensor “low” or reference voltage codes stored at the same time$50 to $400
Signal wire shorted to ground or chafed harnessHarness rubbing on the engine or a bracket; 5 volts present but signal near zero$50 to $300
Failed MAP sensorGood supply and ground at the plug, signal still near zero$80 to $250 installed
Engine computer connector or ground faultSeveral unrelated sensor codes; corrosion or water at the computer$50 to $300
Engine computer faultEvery circuit tests good and the signal is still read as low$500 to $1,500

Get it checked promptly if the engine stalls, hesitates badly, has very little power or has gone into a reduced-power mode. On engines that calculate fuel from the MAP signal, a reading stuck low tells the computer the engine is barely loaded, so it can under-fuel badly under acceleration, and a stall in traffic is the real risk. If the engine runs normally and P0107 is the only code, it is generally safe to drive for a short time while you arrange the checks below.

What the P0107 Code Actually Means

The MAP sensor measures the absolute pressure inside the intake manifold. It is usually a three-wire sensor mounted on the intake manifold or connected to it by a short hose. The engine computer feeds it a regulated 5-volt reference and a ground, and the sensor returns a signal voltage that rises with pressure. The standard definition of P0107 is “Manifold Absolute Pressure/Barometric Pressure Circuit Low Input” or, in GM’s wording, “Manifold Absolute Pressure (MAP) Sensor Circuit Low Voltage”.

On a typical naturally aspirated engine the readings fall into a familiar pattern:

  • Key on, engine off: the manifold is at atmospheric pressure, so the signal sits near the top of its range, typically around 4 to 4.5 volts at sea level and a little lower at altitude.
  • Warm idle: the manifold is under strong vacuum, which is low absolute pressure, so the signal drops to roughly 1 to 1.5 volts.
  • Wide-open throttle: vacuum collapses and the signal climbs back toward the key-on value. On turbocharged engines, which use a sensor with a wider range, it rises further under boost.

P0107 sets when the signal falls below the bottom of that range, a level even the highest manifold vacuum cannot produce. Exact thresholds and timers vary by manufacturer and sensor type, so use the service information for your vehicle for precise figures.

Why a Vacuum Leak Cannot Cause P0107

Because the sensor measures absolute pressure, more vacuum means a lower reading and less vacuum means a higher one. A vacuum leak lets outside air into the manifold, which raises manifold pressure, so the MAP voltage goes up. A cracked or disconnected hose between the manifold and a remotely mounted MAP sensor does the same thing: the sensor simply reads atmospheric pressure and reports a high, flat signal.

So the mechanical faults people usually suspect first produce readings that are high or implausible. Those faults set P0106, the range or performance code, rather than P0107. A signal at the floor of the scale has only electrical explanations. That is the single most useful thing to know about this code: start with the wiring and the sensor’s power supply, not with a smoke machine.

The fastest way to prove it is to turn the key on with the engine off and read the MAP value on a scan tool. A healthy circuit shows something close to barometric pressure: around 100 kPa, about 29 to 30 inHg or about 14.7 psi at sea level. If it reads near zero with the engine stopped, the fault is electrical, full stop.

Symptoms You May Notice Alongside the Code

How much you notice depends on how the engine uses the MAP signal. Engines that calculate fuel mainly from manifold pressure, known as speed-density systems, are affected most. Engines with a mass airflow sensor use the MAP signal for checks and corrections, so the effect is often milder.

  • The check engine light, often with no other change on MAF-equipped engines
  • Hesitation, stumbling or a lack of power under acceleration
  • Stalling, a rough idle or a hard start
  • A reduced-power or limp mode, or other warning messages on some vehicles
  • Poor fuel economy as the computer falls back on default values
  • Other codes: P0108 or P0106 from the same sensor, reference voltage codes, or turbo underboost codes on diesels and turbocharged engines

On some vehicles the symptoms reach well beyond the engine. Ford’s TSB 19-2212 for 2018 to 2019 Explorer, Flex, Taurus and Lincoln MKT models with the 3.5-liter EcoBoost lists a malfunction indicator lamp, the powertrain malfunction (wrench) lamp, a Service AdvanceTrac message, a Hill Start Assist Not Available message and lack of power, all with P0107, P0108 and/or P0109.

1. Loose, Corroded or Poorly Crimped Connector

The MAP sensor sits on top of the engine, where it sees constant heat cycling and vibration. A connector that is not fully latched, a terminal that has spread and lost its grip, or a crimp that has loosened inside the terminal can interrupt the signal or the 5-volt supply. The result is a signal that drops to zero, briefly or permanently.

This is a documented failure, not a theory. GM’s preliminary information PI0759 for 2011 to 2012 Chevrolet Express and Silverado and GMC Savana and Sierra trucks with the Duramax diesel covers P0106, P0107, P0108, P0299 and P2263 with a Reduced Engine Power message. It attributes them to “intermittent conditions and poor connections in the MAP sensor connector wiring harness terminal crimps”. The fix is a new connector pigtail, not a new sensor.

Check the connector before anything else. Make sure it clicks fully home, look for green corrosion or oil inside it, and with the engine idling and a scan tool showing MAP, gently wiggle the connector and harness. If the reading jumps or drops out, you have found it.

2. Shorted 5-Volt Reference Circuit

The MAP sensor rarely has a 5-volt supply to itself. Engine computers usually feed several sensors from one reference circuit, often including the throttle position sensor, accelerator pedal sensors, fuel tank pressure sensor, A/C pressure sensor or camshaft sensors, depending on the engine. If any of those sensors or their wiring shorts the shared reference to ground, every sensor on it loses power at once and reads low.

The giveaway is a cluster of codes. P0107 alongside other “circuit low” codes, or a sensor reference voltage code such as P0641 or P0651, points to the shared supply rather than the MAP sensor. Measure the reference at the MAP connector with the key on. If it is well below 5 volts, unplug the other sensors on that circuit one at a time until it recovers. The one that brings it back is the culprit, and a new MAP sensor would not have helped.

3. Signal Wire Shorted to Ground or a Chafed Harness

If the 5-volt reference and ground are good at the connector but the signal is still near zero, the signal wire may be shorted to ground somewhere between the sensor and the computer. Harnesses on top of the engine can rub through on brackets, the edge of the intake or the throttle body, and rodents chew them on parked cars.

With the sensor and computer unplugged, check the signal wire for continuity to ground. It should have none. Then check it end to end for continuity, and follow the harness by eye for shiny, worn or chewed insulation.

4. Failed MAP Sensor

MAP sensors do fail internally, and when they do they often fail toward one end of the scale. Ford’s TSB 19-2212 treats the sensor as the fix on the affected EcoBoost models: the service procedure is simply to replace the manifold absolute pressure and temperature (MAPT) sensor, with 0.3 hour of labor allowed.

Before replacing the sensor on any other vehicle, confirm it is the sensor. With the connector plugged in and the key on, back-probe the three wires. You should see about 5 volts on the reference, close to 0 volts on the ground and a signal near the barometric value described above. If reference and ground are good and the signal is still near zero, the sensor has failed. Some sensors also let you apply vacuum with a hand pump and watch the signal fall smoothly as vacuum rises. A dead or erratic response confirms the diagnosis.

When buying a replacement, match the part to the engine exactly. Turbocharged and diesel engines use sensors with a wider pressure range, and on many engines the MAP sensor also contains the intake air temperature sensor.

5. Engine Computer Connector or Ground Fault

The computer end of the circuit can fail too. Water getting into the engine computer’s connector, a corroded terminal or a poor computer ground can disturb several sensor signals at once, and P0107 is often among the first codes to show up because the MAP circuit is so sensitive. Several unrelated sensor codes appearing together, especially after heavy rain, a car wash or engine bay cleaning, point here.

Inspect the computer connectors for moisture and corrosion and check the computer’s ground connections for voltage drop. Those faults are usually far cheaper to fix than the computer itself.

6. Engine Computer Fault

A failed computer input or 5-volt regulator can cause P0107, but it is the least likely cause and the last to accept. It becomes a real possibility only when the sensor is new and correct, the wiring checks out end to end, and the computer still reports a low reading or still cannot supply a steady 5-volt reference with every sensor on that circuit unplugged. Check for software updates for your vehicle before replacing a computer, and expect the replacement to need programming.

How to Diagnose P0107 in the Right Order

  1. Read every stored code and the freeze frame. Reference voltage codes or several “circuit low” codes at once point to the shared 5-volt supply. P0107 alone points to the MAP sensor, its connector or its own wiring.
  2. Check for service bulletins on your vehicle in NHTSA’s database. Bulletins such as Ford’s 19-2212 and GM’s PI0759 identify the known fix directly.
  3. Do the key-on, engine-off check. MAP should read close to barometric pressure. A reading near zero confirms an electrical fault.
  4. Inspect and wiggle-test the connector and harness with the engine idling and MAP in live data.
  5. Back-probe the sensor connector: about 5 volts reference, near-zero ground, and a signal that matches conditions.
  6. If the reference is low, unplug the other sensors on the same circuit one at a time until it recovers.
  7. If reference and ground are good, check the signal wire for a short to ground and continuity to the computer. If the wire is good, replace the sensor.
  8. Clear the codes and confirm the repair with a drive that covers idle, light cruise and full throttle while watching MAP respond.

What not to do: do not spend money on a smoke test, a new intake gasket or vacuum hoses for P0107 alone, because those faults raise the MAP reading rather than lowering it. Do not replace the MAP sensor if other sensor codes are stored with it until the shared reference has been checked. And do not swap the engine computer until the wiring and reference have been proven good.

P0107 Repair Cost

These are typical ranges for common cars and light trucks. Most MAP sensors are easy to reach, so labor is usually short, though a few are buried under intake components.

RepairTypical Cost
Diagnostic fee at a shop$100 to $180
Connector cleaning or reseating$0 to $100
Connector pigtail replacement$50 to $200
MAP sensor, part only$30 to $150
MAP sensor, installed$80 to $250
Wiring repair or shared-reference fault$50 to $400
Engine computer, installed and programmed$500 to $1,500

A MAP sensor swap is one of the simpler DIY jobs on most engines: usually one or two bolts and a connector. The diagnosis is what saves money, since the sensor is only the answer in some P0107 cases.

Can You Keep Driving With P0107?

On many engines with a mass airflow sensor, P0107 alone causes little or no change in how the car drives, and short-term driving is generally fine while you arrange the repair. Expect the car to fail an emissions inspection, and expect some loss of fuel economy.

On speed-density engines, and on turbocharged and diesel engines that use the MAP signal for boost control, the effect can be serious: hesitation, a sudden loss of power, reduced-power mode, or stalling. A car that stalls or will not accelerate properly is unsafe when merging or crossing traffic, so get it fixed before relying on it. If the shared 5-volt reference is shorted, other sensors such as the throttle or pedal sensors may be affected as well, which is another reason to repair it promptly.

Related Codes

  • P0106: MAP sensor range or performance. The reading is believable but does not match what the engine is doing, so vacuum leaks, a blocked or split sensor hose and mechanical faults are suspects as well as the sensor.
  • P0108: the opposite of P0107, the signal is too high. Typically an open ground, a short to voltage or a failed sensor.
  • P0109: the MAP signal is intermittent, which often points to the connector.
  • P0102: the mass airflow sensor’s circuit is low. A different sensor, but the same kind of fault and the same first checks: connector, supply and ground.
  • P0113: intake air temperature sensor circuit high. On engines where the MAP and air temperature sensors share one housing and connector, a connector fault can set P0107 and P0113 together.
  • P0299: turbo underboost. On turbocharged engines a bad MAP or boost signal can set it alongside P0107, so fix the circuit fault first.

If the engine idles roughly or stalls while you track this down, the guide to vacuum leak symptoms and how to find one covers the faults that set P0106 instead.

P0107 Questions Answered

What does the P0107 code mean?

P0107 means the engine computer is reading a voltage from the manifold absolute pressure (MAP) sensor that is lower than the sensor should ever produce. It is an electrical fault: usually a poor connector, a lost or shorted 5-volt supply, a signal wire shorted to ground or a failed sensor.

Can a vacuum leak cause P0107?

No. A vacuum leak raises the pressure in the intake manifold, which makes the MAP reading go up, not down. Vacuum leaks and split sensor hoses set P0106, the range or performance code, instead. P0107 points to the circuit and the sensor.

How much does it cost to fix P0107?

Often very little if the fault is the connector, which can cost nothing to reseat or $50 to $200 for a new pigtail. A MAP sensor typically costs $80 to $250 installed. Wiring repairs usually run $50 to $400, and an engine computer, rarely needed, $500 to $1,500.

Is it safe to drive with a P0107 code?

On many engines with a mass airflow sensor, yes, for a short time, because the car may drive almost normally. On engines that rely on the MAP signal for fueling or boost control, P0107 can cause hesitation, reduced power or stalling, and the car should be fixed before you rely on it in traffic.

How can I tell if the MAP sensor is bad or the wiring is?

Turn the key on with the engine off and read MAP on a scan tool. It should show close to barometric pressure. Then back-probe the connector: about 5 volts on the reference and near zero on the ground. If both are good and the signal is still near zero, the sensor has failed. If the reference is low, the wiring or another sensor is at fault.

What is the difference between P0106, P0107 and P0108?

All three come from the MAP sensor circuit. P0106 means the reading is believable but does not match engine conditions, often from a vacuum leak or hose problem. P0107 means the signal is too low and P0108 means it is too high, both of which are electrical faults in the sensor or its wiring.

As an Amazon Associate we earn from qualifying purchases.

About the author

The Motor Guy

The Motor Guy is a passionate car enthusiast with a love for troubleshooting and diagnosing all sorts of vehicle problems. He started TheMotorGuy.com in early 2017 after learning to service and repair his own BMW and VW cars.

With years of experience in OBD diagnostics, and a background in information systems that suits the data side of modern vehicles, he shares practical guides on keeping your vehicle running smoothly. Guides are researched from manufacturer service information, NHTSA recall and safety data and other primary sources, which are cited in each article.

Qualifications:
- First Class Honours Degree in Information Systems