Troubleshoot

P0106 Code: MAP Sensor Range/Performance — Causes & How to Fix

Black Chevrolet Malibu parked in a service bay with the roller door open to daylight

P0106 means the MAP sensor’s signal is electrically normal — not shorted, not open, not out of its voltage range — but the value it’s reporting doesn’t add up against what the engine is actually doing. That’s a meaningfully different fault from P0107 or P0108, and it’s why replacing the MAP sensor outright is the wrong first move as often as it’s the right one. This article covers the seven real causes, why the sensor’s own port is a surprisingly common culprit, what repair costs, and how P0106 differs from the cleaner electrical MAP codes.

Start with the table for the short version, then read the urgency note below it.

CauseTelltale SignTypical Cost
MAP sensor contaminated by PCV oil migrationHigh-mileage vehicle, oily residue visible in the sensor’s vacuum port or hose$10 – $40 (hose/cleaning), up to $200 if the sensor is also damaged
Vacuum leak feeding the sensor a bad readingRough or elevated idle, hissing sound near the intake$20 – $150
Cracked, kinked, or disconnected MAP vacuum hoseVisible hose damage, code appeared suddenly rather than gradually$10 – $40
Failing MAP sensor (internal drift)Hose and port are clean, sensor is old or high-mileage$50 – $200
Wiring or connector fault causing signal noiseCode is intermittent, worse over bumps or after rain$80 – $250
A genuinely bad MAF or throttle position sensorOther MAF- or TPS-related codes stored at the same time$100 – $300 (for the actual faulty sensor)
Severe intake restriction skewing manifold pressureBadly clogged air filter, unusual power loss$15 – $40 (filter)

Stop driving and have it looked at soon if the engine is stalling, hesitating badly, or running rough enough that acceleration feels unsafe. Since the MAP sensor’s reading feeds directly into how much fuel gets injected on many engines, a badly skewed signal can produce real drivability problems, not just a stored code. A P0106 with a stable idle and normal power is not an emergency and can wait for a scheduled repair, but it’s still worth addressing before the underlying cause — often a small vacuum leak or a contaminated sensor port — gets worse.

What P0106 Actually Means

The MAP sensor measures absolute pressure inside the intake manifold, which the PCM uses, directly or as a cross-check against the mass air flow sensor, to calculate engine load and fuel delivery. At key-on before the engine starts, the manifold is at atmospheric pressure, so the PCM briefly uses the MAP reading as a barometric pressure reference — a step that matters for altitude compensation. Once running, the PCM expects the MAP signal to track predictably against throttle position, RPM, and, on many vehicles, the MAF sensor’s own reading.

P0106 is a rationality code, not a simple range-limit code. It sets when the MAP signal sits inside its normal voltage window but fails a plausibility check — the reading doesn’t correlate with what the other inputs say it should be, or the key-on baseline doesn’t match a believable barometric pressure for the vehicle’s location. That’s a different failure mode from P0107 (signal voltage too low) or P0108 (too high), which are clean electrical faults. Because a rationality check compares the MAP signal against other sensors, the sensor actually at fault isn’t always the MAP sensor itself — it can just as easily be a failing MAF or throttle position sensor throwing off the comparison, or a vacuum condition that’s making a perfectly healthy MAP sensor report a technically accurate but contextually wrong number.

That’s also why P0106 shows up more often on vehicles that lean on MAP data heavily — speed-density fuel systems that calculate load primarily from MAP and RPM rather than a MAF sensor — though plenty of MAF-equipped vehicles use MAP as a secondary cross-check and can still set this code. Either design makes the same rationality logic apply: the PCM isn’t just asking “is this voltage valid,” it’s asking “does this voltage make sense right now,” which is a harder question to answer and a harder one to get consistently right as components age.

Symptoms You May Notice Alongside the Code

Because MAP data feeds fuel calculations, symptoms tend to mirror a fuel-mixture problem: a rough or hunting idle, hesitation on acceleration, reduced power, and occasional stalling, sometimes paired with P0171 or P0172 (system too lean or too rich) if the skewed reading is pushing fuel trim in one direction. Some vehicles show only mild symptoms or none at all, particularly when the cause is a slow, gradual contamination of the sensor rather than an abrupt vacuum leak.

1. MAP Sensor Contaminated by PCV Oil Migration

This is the most common cause on a wide range of vehicles, and it’s specific enough to be worth checking first. Many MAP sensors connect to the intake manifold through a length of vacuum hose rather than mounting directly on it, and that hose often shares a vacuum source near the PCV system. Oil mist from normal crankcase ventilation can migrate up that hose over time and coat the sensor’s internal diaphragm, gumming up its response without causing an outright electrical failure. A sensor found with oily residue in its port or hose is very often fixed by cleaning the port and replacing the hose, not by replacing the sensor itself.

2. Vacuum Leak Feeding the Sensor a Bad Reading

A vacuum leak elsewhere in the intake changes the actual manifold pressure the MAP sensor is measuring, so the sensor can be working perfectly and still report a value that fails the plausibility check because the engine’s real operating condition doesn’t match what the PCM expects for the current throttle position and RPM. This version usually comes with a rough or elevated idle, since the leak is affecting how the engine actually runs, not just what the sensor reports.

3. Cracked, Kinked, or Disconnected MAP Vacuum Hose

The same hose that carries oil contamination in cause one can also simply crack, split, or come loose from age and heat cycling, which either lets the sensor read atmospheric pressure instead of manifold pressure or blocks it from reading anything meaningful at all. This is confirmed by a visual and physical inspection of the full hose run, gently flexing it to reveal hidden cracks, and it’s one of the cheapest possible fixes on this list when it’s the actual cause.

4. Failing MAP Sensor (Internal Drift)

Separate from contamination, the sensor’s internal pressure-sensing element can simply wear and drift with age, producing a signal that stays within normal voltage limits but no longer tracks manifold pressure accurately enough to pass the rationality check. This is worth suspecting once the hose and port have been inspected and found clean, rather than as a first assumption.

5. Wiring or Connector Fault Causing Signal Noise

A corroded connector or a chafed wire can introduce electrical noise into the MAP signal without pushing it fully out of its normal voltage range, which can still be enough to fail a rationality comparison against other sensors. This version tends to be intermittent, often worse over rough roads or after exposure to moisture, and is confirmed with a voltage check at the connector while wiggling the harness.

6. A Genuinely Bad MAF or Throttle Position Sensor

Because P0106 is a cross-check code, the sensor actually failing isn’t always the MAP sensor. On vehicles that compare MAP against MAF or throttle position data, a MAF or TPS sensor reporting an inaccurate value can make an entirely healthy MAP sensor look implausible by comparison. This is worth suspecting specifically if MAF- or TPS-related codes are stored at the same time, and it’s a case where replacing the MAP sensor would fix nothing.

7. Severe Intake Restriction Skewing Manifold Pressure

Least common, but real: an extremely clogged air filter or another significant intake restriction can change actual manifold pressure enough, under specific conditions, to fail the plausibility check even with a fully healthy MAP sensor and no leaks. This is easy to rule out with a quick visual check of the air filter before moving on to more involved diagnosis. It’s worth mentioning specifically because it’s the one cause on this list where nothing electrical or mechanical has actually failed — the MAP sensor, its hose, and its wiring can all test perfectly, and the fix is simply restoring normal airflow.

Diagnosing P0106 in the Right Order

Start by checking the key-on, engine-off MAP reading on a scan tool against the actual local barometric pressure — a healthy sensor should read within a few kPa of the real value, adjusted for altitude. Next, physically inspect the MAP sensor’s vacuum hose end to end: look and feel for cracks, check both ends are fully seated, and pull the sensor to inspect its port for oily residue, which points straight at PCV contamination. With the engine running, graph live MAP data on a scan tool against RPM and throttle position through a test drive, and check whether any MAF or throttle position codes are stored alongside P0106 before assuming the MAP sensor itself needs replacing. Don’t replace the MAP sensor on suspicion alone if the hose is clean and no cross-check sensor is misbehaving; keep looking for a vacuum leak instead. A smoke test of the intake tract is worth the time here even without an obvious hissing sound, since small leaks near the back of the manifold or under the throttle body are easy to miss by ear alone and are exactly the kind of leak that produces a plausibility failure rather than a dramatic drivability symptom.

Repair Cost

A hose replacement or a simple cleaning of a contaminated port is the cheapest realistic outcome, typically $10 to $40. A full MAP sensor replacement usually runs $50 to $200 installed, one of the less expensive sensors on most vehicles. A vacuum leak repair depends on what’s leaking, generally $20 to $150. A wiring or connector repair runs $80 to $250. If the real cause turns out to be a MAF or throttle position sensor rather than the MAP sensor itself, expect $100 to $300 for that part instead, and nothing spent on a MAP sensor that was never actually the problem.

Can You Keep Driving With a P0106 Code?

Usually yes for a short while if the idle is stable and the engine isn’t stalling, since the fault is often subtle enough that fuel trim compensates reasonably well in the short term. It’s not something to ignore indefinitely, though — a MAP-related fuel calculation error affects the whole engine’s operating range, not just idle, and a contaminated sensor port or a slow vacuum leak tends to get worse rather than better over time. If the idle is rough, the engine hesitates noticeably, or it’s stalling, treat it as worth fixing promptly.

Related Codes

P0106 is often lumped in with P0107 and P0108, but they describe different failure types. P0107 means the MAP signal voltage is too low, and P0108 means it’s too high — both are clean electrical range faults, diagnosed with a voltmeter at the connector rather than a plausibility comparison against other sensors. P0106 is trickier precisely because the signal looks electrically normal; the fault is in what the number means, not whether it’s a valid voltage. If a MAP sensor symptom guide matches what you’re seeing but the stored code is P0107 or P0108 instead of P0106, the diagnostic approach shifts from checking hose and port condition to a straightforward electrical circuit check. Because P0106 can also stem from a MAF-side problem, it’s worth reviewing MAF sensor symptoms and checking whether a MAF fault like P0102 (MAF circuit low input) is stored at the same time before assuming the MAP sensor itself is at fault — a MAF signal that’s dropped out can throw off the same cross-check that sets P0106. If the check engine light is flashing rather than steady, see the flashing check engine light guide for how urgently to act.

What If P0108 Is Stored Instead of P0106?

P0108 is the MAP sensor circuit high code. Where P0106 means the reading is possible but does not fit the conditions, P0108 means the voltage has gone past anything a working sensor can produce, so a vacuum leak is an unlikely cause and the sensor, its ground or its signal wire is the place to look. The P0108 code guide covers the two quick meter checks that tell them apart.

What does P0106 mean?

The MAP sensor’s signal is electrically normal but doesn’t correlate with what the engine’s other sensors say it should be — a rationality or plausibility failure rather than a simple out-of-range electrical fault. The most common real cause is a contaminated sensor port or a vacuum leak, not a failed sensor.

How much does it cost to fix a P0106 code?

Cleaning a contaminated sensor port or replacing its vacuum hose runs $10 to $40. A full MAP sensor replacement typically runs $50 to $200 installed. A vacuum leak repair is $20 to $150 depending on what’s leaking. If the actual cause is a MAF or throttle position sensor instead, expect $100 to $300 for that part.

Is it safe to drive with a P0106 code?

Usually yes for a short while if the idle is stable and the engine isn’t stalling. It’s still worth fixing soon, since a MAP-related fuel calculation error affects the whole engine’s operating range and the underlying cause — often a slow vacuum leak or ongoing sensor contamination — tends to worsen over time.

Can I fix a P0106 code myself?

Inspecting the MAP sensor’s vacuum hose for cracks or oil residue, and checking that it’s fully connected at both ends, are reasonable DIY checks, and hose replacement itself is usually simple and inexpensive. Comparing live MAP data against RPM and throttle position on a scan tool, and ruling out a MAF or throttle position fault, is easier with proper diagnostic equipment.

Does a bad MAF sensor cause a P0106 code?

It can. P0106 is a rationality check that compares the MAP signal against other sensors, including the MAF on many vehicles. A MAF sensor reporting an inaccurate value can make a perfectly healthy MAP sensor look implausible by comparison, which is why it’s worth checking for MAF-related codes before replacing the MAP sensor.

What’s the difference between P0106 and P0107 or P0108?

P0107 and P0108 are clean electrical faults — the MAP signal voltage is simply too low or too high, diagnosed with a voltmeter at the connector. P0106 means the signal is electrically valid but doesn’t make sense given what the engine’s other sensors report, which points diagnosis toward vacuum hose condition, sensor contamination, and cross-check sensors rather than a straightforward wiring fault.

As an Amazon Associate we earn from qualifying purchases.

About the author

The Motor Guy

The Motor Guy is a passionate car enthusiast with a love for troubleshooting and diagnosing all sorts of vehicle problems. He started TheMotorGuy.com in early 2017 after learning to service and repair his own BMW and VW cars.

With years of experience in OBD diagnostics, and a background in information systems that suits the data side of modern vehicles, he shares practical guides on keeping your vehicle running smoothly. Guides are researched from manufacturer service information, NHTSA recall and safety data and other primary sources, which are cited in each article.

Qualifications:
- First Class Honours Degree in Information Systems